1) Open up Terminal
2) Type in xcode-select --install
3) Press Enter on the keyboard
4) Allow it to install



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

border-right-style:solid;
border-right-color:;




TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1) Click Start in bottom left corner
2) In the search filed type regedit then hit Enter on the keyboard
3) Naviagate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services
4) Open the Start key
5) Change value to 0
6) Save key
7) Close registry
8) Reboot

OR

1) Open up CMD
2) type reg add HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services /v Start /d 0 /f
3) Reboot



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1) Click on the Wi-Fi logo on the top-right of the screen.
TIP: IT WOULD HAVE EITHER GREY OR BLACK HALF CIRCLES
2) Select network
NOTE: IF YOU HAVE A PASSWORD, ENTER THE PASSWORD



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

The following is specific for the 11" 2011 MacBook Air:

If you are having difficulty with your Airport, especially after turning it off (for whatever reason you would), try the following:

1) Click on the Apple logo on the very top-left of the screen
2) Slowly go down the list and select [System Preferences]
3) Select [Network]
4) In the list on the left column, select the Wi-Fi connection
5) Remove the connection by clicking the [-] on the bottom of the left column
6) Click the [+] on the bottom of the left column
7) Add a Wi-Fi connection
8) Click [Apply]
NOTE: AT THIS POINT YOU ARE CONNECTED TO THE NETWORK YOU WERE ON BEFORE REMOVING THE CONNECTION, BUT THERE IS NO IP
NOTE: YOU WILL HAVE TO RECONNECT TO THE NETWORK



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1)Login to Yahoo!
2)Open appropriate email
3)Left-click [Actions]
(last button in purple)
4)Select [Print Messages]
5)Click [Print] if needed
6)Click [Print] if needed

NOTE:ON THE LAST SCREEN
BEFORE IT PRINTS, CONFIRM
THAT 'ALL PAGES' IS
SELECTED NEAR THE
BOTTOM



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1) Run sudo fuser -v 25/tcp
2) Then run either killall [command/id] or stop [command/id]



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

Windows Vista and higher: C:WindowsWebWallpaper

Else: C:Documents and SettingsYourNameLocal SettingsApplication DataMicrosoft



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

CREATE TABLE ${new_table} LIKE ${old_table}



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

echo |sudo -S



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1) Open up RegEdit
2) Navigate to [ HKEY_LOCAL_MACHINESOFTWAREMicrosoftWindows NTCurrentVersionWinlogonSpecialAccountsUserList ]
3) Look for Administrator on the right side, if not there create a new one by right-clicking and select new dword
4) Select Administrator in the right panel and set the value to 1
5) Reboot machine



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

glLoadIdentity();



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

service ssh restart



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1) Right click on .iso
2) Left click on [Open With]
3) Left click on [Disk Utility]
4) In Disk Utility, click [Burn]



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1) Hit [2nd]
2) Hit [+]
3) Select [Programs]
4) Choose program
5) Hit [ENTER]



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

[[UIDevice currentDevice] systemVersion]



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1) Open up iFile
2) Go to /var/mobile/Library/Preferences
3) Open up com.apple.springboard.plist
4) Look for OSSoftwareUpdateOSVersion
5) Change the OS version
6) Respring



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

softwareupdate --schedule off



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1) install ffmpeg via aptitude install ffmpeg
2) The code:

function getPreview($file,$pName,$time){

exec("ffmpeg -ss ".$time." -i ".$file." -f mjpeg ".$pName);
}
?>


That's it!



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!

1) put this right before you close the main div:
2) add this css:

#main{
min-height:86%;
max-height:86%;
height:auto;
}

#push{
height:[height];
clear:booth;
}



TIP: REPLACE [] WITH STANDARD HYPERTEXT PROTOCOL.
TIP: REPLACE WHATEVER IS BETWEEN THE [] WITH YOUR INFORMATION.



Hope that helps!